基于平面复合降阻材料的杆塔基础接地降阻研究

杆塔基础自然接地作为输电线路重要的接地装置,能减少外延接地及降阻施工成本。针对特高压输电线路杆塔基础接地提出基于平面复合降阻材料的塔基外敷接地降阻策略,首先,采用CDEGS仿真计算软件建立特高压杆塔单根浇注桩接地计算模型,分析均匀土壤、多层土壤、混合土壤三种条件下的外敷接地降阻效果;然后,通过单个塔基外敷计算模型分析外敷材料不同敷设方式的降阻效率;最后,计算完整杆塔基础外敷接地降阻效率和散流分布特征,并与水平人工外延接地降阻方式进行对比。结果表明,外敷接地降阻效率与土壤条件、敷设位置等因素有关,在高土壤电阻率条件下,塔基外敷接地降阻效率超过22%,与水平人工外延接地相比,塔基外敷接地降阻的散流比超过96%,接地材料利用率高,可减少征地和二次接地施工成本。     

Fe基非晶合金增强1060铝基多层复合材料的组织与性能

采用累积叠轧焊+中间退火法复合轧制1060Al/Fe基非晶多层铝合金复合板材。利用光学显微镜、扫描电镜、X-衍射分析仪以及拉伸试验机分析Al基复合材料的微观组织结构变化、断口形貌、物相组成以及力学性能。结果表明:Fe基非晶复合材料的增强体在300 ℃中间退火过程中发生部分晶化,在累积变形轧制过程中发生破碎,并随着变形道次的增加,破碎程度随之增大;复合板前6道次的累积轧制变形出现了明显的加工软化现象,并且随着变形道次的增加,其加工软化的效果愈明显;随着累积轧制变形道次增加,Al基复合材料的力学性能发生了明显的变化,第2道次轧制变形后屈服强度与抗拉强度达到了最大值为140 MPa和156 MPa,伸长率为5.53%,达到最佳综合性能。     

Electrochemical corrosion behavior of LDX 2101® duplex stainless steel in a fluoride-containing environment

The effect of fluoride on the electrochemical corrosion behavior of an LDX 2101® duplex stainless steel (DSS) was studied. Open-circuit potential (E_OC) and electrochemical impedance spectroscopy (EIS) measurements were carried out in artificial saliva and with the addition of fluoride (1 wt% NaF). The electrochemical corrosion behavior of the AISI 316L austenitic stainless steel (SS) was also evaluated for comparison. Both open-circuit potential and EIS results indicate that DSS and austenitic SS undergo spontaneous passivation due to spontaneously formed oxide film passivating the metallic surface, in the simulated aggressive environments. However, LDX 2101® exhibits superior corrosion resistance as compared with AISI 316L, and this improvement is ascribed to the formation of a passive film which shows a higher protective effect than the one formed on AISI 316L.     

有机膜精确调控传质的新型溶析结晶及过程强化

溶析结晶是一种环保、高效的结晶方法，在温敏性、低溶解度物系的晶体生产领域具有不可替代的重要作用。但是，传统溶析结晶过程中溶液过饱和度的时空均一性差，传质调控为微米级尺度，容易爆发成核，是亟待解决的关键问题。本文提出利用聚醚砜（PES）中空纤维膜，为溶析剂与结晶溶液之间的传质提供均匀稳定的界面，实现结晶溶液与溶析剂的精确混合和结晶过程强化，开发了一种新型的溶析结晶传质调控技术。溶析剂在压力差驱动下均匀渗透通过有机膜，在结晶溶液一侧的膜外表面形成溶析剂液膜层，通过表面液膜的不断更新，将传统溶析结晶的毫米级宏观混合转变为亚微米级尺度的微观混合，实现过饱和度的均匀分布。同时，这层液膜的存在，避免了结晶溶液直接接触膜表面，有效地解决了异相成核附着导致膜污染的问题。实验中，对壳程流速做出周期性改变后，渗透通量可即时发生一致的线性响应变化，证实有机膜调控传质过程的精确性和灵敏性。PES膜重复使用多次后，渗透通量仍可以保持稳定。相比传统的滴加式溶析结晶，在相同的溶析剂传质速率下，有机膜调控过程制备的晶体产品，形貌更加规整、粒径分布更集中。因此，在溶析剂精确传质和抗污染方面，有机膜调控的溶析结晶过程均表现出良好的性能，为药物、大分子结晶的高效工业化制备开拓了新的思路。     

超声振动光整的EDEM数值模拟与实验研究

采用EDEM离散元分析软件对普通钝化光整实验及带有超声振动辅助光整实验进行数值模拟，仿真结果为超声振动光整加工系统的提出提供了依据。使用超声振动光整设备对平头铣刀进行钝化实验，进行了不同钝化条件下的实验研究。通过扫描电镜观察了钝化前后铣刀的表面形貌及钝圆半径的变化，分析了超声振动光整对钝化效率及效果的影响。实验结果表明，增加了超声振动钝化后的钝化效率提高了约26%，表面形貌得到较大改善。     

Size controlled synthesis of well-distributed nano-silver on hydroxyapatite using alkanolamine compounds

A well-distributed nano-silver hydroxyapatite composite has been successfully prepared by a one-pot synthesis method. Hydroxyapatite was separately synthesized by a sol-gel method, then impregnated with silver nanoparticles with the mediation of Uncaria gambir Roxb. leaf extract in the presence of three kinds of alkanolamine compound; monoethanolamine (MEA), diethanolamine (DEA), and triethanolamine (TEA) as capping agents. The effect of different capping agents on the properties of the silver nanoparticles and the nano-silver hydroxyapatite composite were studied. UV–visible spectrophotometer analysis exhibited absorbance peaks at 402–439 nm which specifically corresponds to spherical silver nanoparticles. Higher optical absorbance was observed in TEA-capped silver nanoparticles, than in DEA and MEA-capped ones. X-ray diffraction (XRD) analysis showed a highly crystalline hexagonal structure for hydroxyapatite and no detected metallic silver. However, the presence of 1.65% silver was confirmed by energy dispersive x-ray (EDX) spectroscopy analysis. Transmission electron microscopy (TEM) analysis revealed spherical silver nanoparticles with a size range of 2–62 nm (smallest mean diameter of 2 nm) adhered to the hydroxyapatite surface. The TEA capped impregnated silver nanoparticles were the smallest, corresponding to the best capping performance, followed by those capped by DEA and MEA. Small-sized nanoparticles on hydroxyapatite are beneficial for highly antibacterial bone implants.     

Durable,Sensitive, and Wide‐Range Wearable Pressure Sensors Based on Wavy‐Structured Flexible Conductive Composite Film

Flexible pressure sensors have potential applications in human motion monitoring and electronic skins. To satisfy the practical applications, pressure sensors with a high sensitivity, a low detection limit, a broad response range, and an excellent stability are highly needed. Here, a piezoresistive pressure sensor based on wavy‐structured single‐walled carbon nanotube/graphite flake/thermoplastic polyurethane (SWCNT/GF/TPU) composite film is fabricated by a prestretching process. Due to the random wavy structure, high conductivity, and good flexibility, the prepared sensor displays a low detection limit of 2 Pa, a wide sensing range of 0–60 kPa, and a high sensitivity of 5.49 kPa^?1 for 0–50 Pa. Furthermore, the sensor shows a remarkable repeatability of over 1.1 × 10⁴, 9.0 × 10³, and 2.0 × 10³ pressure loading/unloading cycles at 50 Pa, 500 Pa, and 30 kPa, respectively, and a fast responsibility of 100–150 ms of loading response time and 400–600 ms of relaxation time. Therefore, the pressure sensor is successfully adopted to monitor both the large‐scale human activities (e.g., walk and jump) and the small‐scale signals (e.g., wrist pulse). Furthermore, a sensor array is assembled to map the weight and shape of an object, indicating its various potential applications including human–machine interactions, human health monitoring, and other wearable electronics.     

硼氢化钠对滑轮用铸钢板化学镀Ni-B合金薄膜性能的影响

在滑轮用铸钢板上化学镀Ni-B合金薄膜,并研究了硼氢化钠的质量浓度对化学镀Ni-B合金薄膜性能的影响。结果表明:适当增加硼氢化钠的质量浓度,有利于增大化学镀Ni-B合金薄膜的厚度及硼的质量分数,从而提高化学镀Ni-B合金薄膜的硬度。当硼氢化钠的质量浓度大于1.2 g/L时,硼氢化钠的水解速率加快及剧烈的析氢反应,导致化学镀Ni-B合金薄膜的厚度及硬度有所降低。当硼氢化钠的质量浓度为1.2 g/L时,化学镀Ni-B合金薄膜表面"胞状"颗粒均匀、致密,摩擦因数和磨损率最低,具有最佳的耐磨性。     

Composite mixed matrix membranes incorporating microporous carbon molecular sieve as filler in polyethersulfone for CO2/CH4 separation

Membrane technology has been considered a key factor for sustainable growth in high-efficiency gas separation. Current mixed matrix membranes (MMMs) technology is rising, but these membranes in the dense structure are having difficulties in operating at high pressures and scale up for commercialization. The purpose of this research is to synthesize composite MMMs (CMMMs) consisting of polyethersulfone (PES), carbon molecular sieve (CMS 1–5 wt %), and Novatex 2471 nonwoven fabric (support layer). The membranes' physical, chemical, and thermal properties were evaluated by different analytical equipment. The morphology of both PES and PES-CMS composite membranes had a porous and asymmetric structure, in which CMS was uniformly distributed in the polymer matrix. The thermal properties showed that the membranes were stable up to 350 °C with a single glass transition temperature. The functional groups in the membrane were confirmed by spectral analysis. The gas performance results showed that carbon dioxide permeance increased with increased CMS concentration and methane permeance decreased due to the hindering effect of CMS under similar operating conditions. The highest selectivity achieved was 12.774 using CMMM of 5 wt % of CMS at 10 bar, which on average was 137.80%, improved selectivity compared to pure PES membrane. The support layer was able to withstand high operating pressures and showed the ability to scale up. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48476.     

RTM制备玻璃纤维增强环氧树脂复合材料的力学性能分析

以环氧树脂为基体,短切玻璃纤维和玻璃纤维布为增强材料,通过RTM工艺制备了玻璃纤维增强环氧树脂(GF/EP)复合材料,并研究了RTM工艺制备玻璃纤维布增强环氧树脂(L-GF/EP)和短切玻璃纤维增强环氧树脂(S-GF/EP)复合材料的拉伸和弯曲性能,分析了开孔对两种复合材料拉伸性能的影响。结果表明:在拉伸过程中,开孔试样因孔边产生的应力集中,导致其拉伸强度与无孔试样相比下降了30%左右;玻纤铺层类型的不同对复合材料的力学性能具有显著影响;L-GF/EP复合材料内部结构完整,在载荷作用下,复合材料的弯曲断裂呈现一定的假塑性断裂模式,达到弯曲极限挠度值后,出现一定程度的回弹现象,其力学性能优于S-GF/EP复合材料。